View 74V1G14S_1030980.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
74V1G14
SINGLE SCHMITT INVERTER
s s
s s s
s
s
s
HIGH SPEED: tPD = 5.5 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1 A (MAX.) at TA = 25 oC TYPICAL HYSTERESIS: Vh = 1V AT VCC=4.5V POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 5.5V IMPROVED LATCH-UP IMMUNITY
S (SOT23-5L)
C (SC-70)
ORDER CODE: 74V1G14S 74V1G14C regard to the supply voltage. This device can be used to interface 5V to 3V. Pin configuration and function are the same as those of the V1G04 but the V1G14 has hysteresis. This together with its schmitt trigger function allows it to be used on line receivers with slow rise/fall input signals. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage.
DESCRIPTION The 74V1G14 is an advanced high-speed CMOS SINGLE SCHMITT INVERTER fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provide high noise immunity and stable output. Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no
PIN CONNECTION AND IEC LOGIC SYMBOLS
October 1999
1/7
74V1G14
INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
PIN No 1 2 4 3 5 SYMBOL N.C. 1A 1Y GND VCC NAME AND FUNCT ION Not Connected Data Input Data Output Ground (0V) Positive Supply Voltage
TRUTH TABLE
A L H Y H L
ABSOLUTE MAXIMUM RATINGS
Symbol VCC VI VO IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 20 25 50 -65 to +150 260 Unit V V V mA mA mA mA
o o
ICC or IGND DC VCC or Ground Current
C C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VI VO Top Supply Voltage Input Voltage Output Voltage Operating Temperature Parameter Valu e 2.0 to 5.5 0 to 5.5 0 to VCC -40 to +85 Unit V V V
o
C
2/7
74V1G14
DC SPECIFICATIONS
Symb ol Parameter T est Cond ition s V CC (V) Vt+ High Level Input Voltage Low Level Input Voltage Hysteresis Voltage 3.0 4.5 5.5 Vt3.0 4.5 5.5 Vh 3.0 4.5 5.5 VOH High Level Output Voltage 2.0 3.0 4.5 3.0 4.5 VOL Low Level Output Voltage 2.0 3.0 4.5 3.0 4.5 II ICC Input Leakage Current Quiescent Supply Current 0 to 5.5 5.5 I O =-50 A IO=-50 A IO=-50 A IO=-4 mA IO=-8 mA I O=50 A IO=50 A IO=50 A IO=4 mA IO=8 mA VI = 5.5V or GND VI = VCC or GND 0.3 0.4 0.5 1.9 2.9 4.4 2.58 3.94 0.0 0.0 0.0 0.1 0.1 0.1 0.36 0.36 0.1 1 2.0 3.0 4.5 Min. 2.2 3.15 3.85 0.9 1.35 1.65 1.2 1.4 1.6 0.3 0.4 0.5 1.9 2.9 4.4 2.48 3.8 0.1 0.1 0.1 0.44 0.44 1.0 10 A A V V Typ . Value T A = 25 o C Max. -40 to 85 o C Min . 2.2 3.15 3.85 0.9 1.35 1.65 1.2 1.4 1.6 V V V Max. Un it
AC ELECTRICAL CHARACTERISTICS (Input t r = tf =3 ns)
Symb ol Parameter V CC (V) tPLH tPHL Propagation Delay Time Test Co ndition CL (pF ) 15 50 15 50 Value T A = 25 o C Min. Typ . Max. 8.3 12.5 10.8 5.5 7.0 16.0 8.6 10.5 Un it -40 to 85 o C Min . Max. 1.0 15.0 1.0 1.0 1.0 18.5 10.0 12.0 ns
3.3(*) 3.3 5.0(**) 5.0(**)
(*)
(*) Voltage range is 3.3V 0.3V (**) Voltage range is 5V 0.5V
CAPACITIVE CHARACTERISTICS
Symb ol Parameter T est Cond ition s Min. C IN CPD Input Capacitance Power Dissipation Capacitance (note 1) Typ . 4 21 Value T A = 25 o C Max. 10 -40 to 85 o C Min . Max. 10 pF pF Un it
1) CPD isdefined as the value of the IC'sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD * VCC * fIN + ICC
3/7
74V1G14
TEST CIRCUIT
CL = 15/50 pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50)
WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle)
4/7
74V1G14
SOT23-5L MECHANICAL DATA
mm MIN. A A1 A2 b C D E E1 L e e1 0.90 0.00 0.90 0.35 0.09 2.80 2.60 1.50 0.35 0.95 1.9 TYP. MAX. 1.45 0.15 1.30 0.50 0.20 3.00 3.00 1.75 0.55 MIN. 35.4 0.0 35.4 13.7 3.5 110.2 102.3 59.0 13.7 37.4 74.8 mils TYP. MAX. 57.1 5.9 51.2 19.7 7.8 118.1 118.1 68.8 21.6
DIM.
5/7
74V1G14
SC-70 MECHANICAL DATA
mm MIN. A A1 A2 b C D E E1 L e e1 0.80 0.00 0.80 0.15 0.10 1.80 1.80 1.15 0.10 0.65 1.3 TYP. MAX. 1.10 0.10 1.00 0.30 0.18 2.20 2.40 1.35 0.30 MIN. 31.5 0.0 31.5 5.9 3.9 70.9 70.9 45.3 3.9 25.6 51.2 mils TYP. MAX. 43.3 3.9 39.4 11.8 7.1 86.6 94.5 53.1 11.8
DIM.
6/7
74V1G14
Information furnished is believed to be accurate and reliable. However, STMicroelectronic s assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics (c) 1999 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com .
7/7

▲Up To Search▲

Price & Availability of 74V1G14S

	To Download 74V1G14S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .